Country Coach Owners Forum

I just got my coach back from Cummins Power Systems. They did two > things, which may have caused the problem, all I know is that it > worked when I dropped it off it worked and now it doesn't.
They (Cummins Power Systems) did their Champagne 0713-Engine > Protection Sensor Update-ISLCM850 and the Onan side replaced a > Generator shaft and bearings which required the removal from the > coach - Generator would shake and rattle off the test bench.

Now I live 3 hours from the nearest CC Repair shop and the Cummins > Power Systems shop that did the work-I think they would direct me > back to CC anyway so I'm trying to fix this on my own.

When I hook up the Tow Cable to my Jeep Liberty (Toad) none of the > lights work (worked prior). Since nothing works (Turn Signals/brake > lights/tail lights) I figured something was not connected on the

cable fuse panel, but all i could find is on Page House 3.19 of the > Owner's guide. I could not find the Electrical Systems Schematics > for this. Looking at Figure 3.15 on Page House 3.19 of the Owner's > guide my board has NO connections maded to the right side (TB2???)

> Have you turned on a turn signal light on the coach and used a volt > meter or test light to see if there is current from the pins in the > coach side connector?

That will tell you if the problem is on the coach side or on the

>

If you need to identify the correct ground pin, there are several > diagrams on the internet that will display the various type of > connector wiring.

I assume from your description that when the toad electical hookup

made, only the Jeep lights do not work? >

Dean

95 CC Magna 5280

[quote author=htbradley1"

>

> I just got my coach back from Cummins Power Systems. They did

things, which may have caused the problem, all I know is that it > > worked when I dropped it off it worked and now it doesn't.
> They (Cummins Power Systems) did their Champagne 0713-Engine > > Protection Sensor Update-ISLCM850 and the Onan side replaced a > > Generator shaft and bearings which required the removal from the > > coach - Generator would shake and rattle off the test bench.
>

> Now I live 3 hours from the nearest CC Repair shop and the

Power Systems shop that did the work-I think they would direct me > > back to CC anyway so I'm trying to fix this on my own.
>

> When I hook up the Tow Cable to my Jeep Liberty (Toad) none of

lights work (worked prior). Since nothing works (Turn

lights/tail lights) I figured something was not connected on the > tow

> cable fuse panel, but all i could find is on Page House 3.19 of

Owner's guide. I could not find the Electrical Systems

for this. Looking at Figure 3.15 on Page House 3.19 of the

guide my board has NO connections maded to the right side

of

> the board-left side all connections used.
>

> When I picked the coach up both the house and chassis battery > > disconnect were off. Reset an all seemed ok except the above.
>

> Any help out there?????
>

> Thanks,

> Terry Bradley
>

[quote author=Dean"

>

> Have you turned on a turn signal light on the coach and used a

meter or test light to see if there is current from the pins in

coach side connector?
>

> That will tell you if the problem is on the coach side or on the > jeep.
>

> If you need to identify the correct ground pin, there are several > > diagrams on the internet that will display the various type of > > connector wiring.
>

> I assume from your description that when the toad electical

is

> made, only the Jeep lights do not work? > >

> Dean

> 95 CC Magna 5280
>
>
>

[quote author=htbradley1"
>]
> >

> > I just got my coach back from Cummins Power Systems. They did > two

> > things, which may have caused the problem, all I know is that

> worked when I dropped it off it worked and now it doesn't.
> > They (Cummins Power Systems) did their Champagne 0713-Engine > > > Protection Sensor Update-ISLCM850 and the Onan side replaced a > > > Generator shaft and bearings which required the removal from

> coach - Generator would shake and rattle off the test bench.
> >

> > Now I live 3 hours from the nearest CC Repair shop and the > Cummins

> > Power Systems shop that did the work-I think they would direct

> back to CC anyway so I'm trying to fix this on my own.
> >

> > When I hook up the Tow Cable to my Jeep Liberty (Toad) none of > the

> > lights work (worked prior). Since nothing works (Turn > Signals/brake

> > lights/tail lights) I figured something was not connected on