Skip to main content ↑ ↓
Topic: Window washer (Read 771 times) previous topic - next topic
0 Members and 1 Guest are viewing this topic.

Window washer

Yahoo Message Number: 85814
The plastic fitting on the body of the coach that the washer line connects to is broken. Where can I get a replacement? Also, I want to replace both the hoses, but they seem to fit in the arms very tight, so I can't get them out and certainly will not be able to run them through there again. What am I missing?

Al Colby

2000 Intrigue 10979

Re: Window washer

Reply #1 –
Yahoo Message Number: 85817
Hi Al,

I stock both new and old style You can order them direct from my web site at theis link or you can call me direct.
Exterior Trim
Thank you
John Davis
JDRV INC.

Your RV / Marine

parts and service professionals

JOHN DAVIS RV SERVICES INC. jd@... 541-306-6473 541-693-3015

Authorized parts and service for
HWH, Roadmaster, Zip Dee,
Dometic, Norcold

Kingdome/King controls,

NOTICE: This message is ONLY for the use of the individual or entity to which it is addressed, and it may contain information that is privileged or confidential. Do not copy or distribute this communication or disseminate its information unless you have been granted specific written authority to do so by the sender. If you have received this communication in error, please notify us immediately by telephone and delete the email from your computer system. Thank you.

Re: Window washer

Reply #2 –
Yahoo Message Number: 85838
Al,

It is good to know that John Davis at JDRV has the parts you need. I had the same problem with my old deteriorated tubing. I am assuming your 2000 Intrigue is similar to my '98 Allure. I took a sample of my old tubing into NAPA and they measured and matched the small diameter. This tubing is much smaller that the standard auto w/s washer tubing carried by most auto parts stores. I removed the old tube by lubing the channel first with wet silicone spray. Then, I pushed with some thick wire from the top while pulling the tubing from the bottom. Then, I squirted some silicone lube into the hoe in the new tubing and inserted about 12" of thin wire into the hole. I left about 15" "leader" of bare wire before cutting it. I lubed the tubing and the channel again, inserted the leader into the wiper arm channel then, slowly pulled and pushed the new tubing into the channel. The thin wire insert gives the tubing just enough rigidity to help when forcing the new tube through the wiper arm channel. Now, remove the leader and proceed with installation to your new fittings.

Hope this helps.

Daron Hairabedian, 98 Allure 30226

Re: Window washer

Reply #4 –
Yahoo Message Number: 85845
Thanks. This is what I needed to know. That tubing is a tight fit!

Al Colby

2000 Intrigue 10979

Re: Window washer

Reply #5 –
Yahoo Message Number: 85868
Al,

I forgot to mention that you should leave plenty of slack as the tubing has a tendency to shrink over time. The tubing deteriorates first at the fittings where it is stretched over the barbs. If you have enough slack, sometimes you can repair by cutting a small amount off of the end and re-connecting Daron

window

Reply #6 –
Yahoo Message Number: 85918
Just wondering. Does anyone know of a method or a tool to replace the rubber gasket that surrounds the screws on the inside of windows. I had to remove a window to fix a leak. This gasket is giving me fits.

Tom Coomes
2005 Inspire
51177

Re: window

Reply #7 –
Yahoo Message Number: 85952
Tom,

Yes! the vinyl insert can be hard on the fingers. There is a tool that is available from C.R. Laurence or your local glass shop. But, it is not really necessary.
Here is a slick glazier's trick. Put the vinyl insert into hot soapy water. When the water cools enough to handle the insert comfortably, it will be pliable enough for easy installation and the soap will do the lubrication. Start at the top center of the window so the the joint will not be visible. Squeeze the vinyl between your thumb and fingers of your right hand as you push it into the channel with your left hand an inch or two at a time. Of course reverse if you are a lefty. Do not use other lubricants as they are messy and do not evaporate, so they continue to lubricate when no longer needed. the soap just dries up and disappears.

Caution: Do not stretch the insert as you are installing it as it will shrink over time and leave a gap at the joint. I usually leave about 1/4" or 3/8" oversize at the end. Then insert at the joint first then, stuff it or "pooch it in" (technical glass industry jargon). This will compensate for the inevitable contraction. Wipe off the residual soap. You are done. Trust me. By the time you finish you will be very proficient at the task. The second time you do this it will be a breeze.
Hope this helps, Tom.
Daron Hairabedian, 98 Allure 30226
 

window

Reply #8 –
Yahoo Message Number: 85933
I use a plastic windshield tool (which can be purchased at many auto paint stores) to insert the screw cover gasket or something with a dull point. Run it along the edge as you work the material. Sometimes it helps to warm up the screw cover insert so it folds into place. Hope this helps.

Regards,
Dave

Dave Rousey Jr. (Owner)
Former CC Technician
Styleworks RV/ Bus
Restoration LLC
4762 Long St.

Sweet Home, OR 97386
(541) 543-7983
daverjr4@...